Imprimez vos orthèses sur mesure, directement dans votre clinique.
Du scan du pied de votre patient aux orthèses finies en quelques heures, sans aucun travail manuel. Conçu par un podiatre pour les professionnels du soin du pied.
Pourquoi Podform3D
- Production en clinique, contrôle clinique total, marges préservées.
- Orthèses prêtes en quelques heures. Pas d'attente de labo. Pas de rendez-vous de suivi.
- Imprimante autonome 72 heures: elle travaille pendant que vous voyez vos patients.
- Zéro personnel dédié à la fabrication, zéro poussière, zéro déchet.
- Opérationnel en 48 heures avec formation complète et support illimité.
Le processus
- Numérisez le pied avec n'importe quel scanner, iPad ou boîte de mousse.
- Configurez la prescription: arche, zones multi-densité, postings, corrections.
- Imprimez sur la bande autonome pendant que vous voyez vos patients.
- Ajustez le recouvrement et livrez le jour même.
Deux chemins
- Impartition via notre réseau de labos certifiés (zéro investissement, livraison 7 jours).
- Production en clinique avec imprimante Podform3D (contrôle total, coût par paire le plus bas).
Questions fréquentes des cliniciens
Ai-je besoin d'expérience en impression 3D pour utiliser le système?
Aucune expérience requise. Podform3D est conçu comme un logiciel clinique, pas comme un outil de bricolage. Vous ne touchez jamais aux réglages 3D, aux calibrations ni aux paramètres techniques. Une intégration guidée de 48 heures vous fait parcourir tout le flux de travail. La plupart des cliniciens produisent leur première orthèse dans les deux jours suivant la réception du système.
Combien de temps avant que ma clinique soit pleinement opérationnelle?
48 heures après la livraison. Cela comprend l'installation physique, la configuration du logiciel, la calibration et une première impression supervisée, tout cela fait avec vous, étape par étape. Aucun service informatique, aucune rénovation, aucun sous-traitant externe. Vous produirez des orthèses pour de vrais patients dès votre première semaine.
Est-ce que je garde le contrôle complet de ce que je prescris?
Entièrement. Vous configurez vous-même chaque paramètre clinique: hauteur de l'arche, profondeur de la cupule talonnière, coin d'avant-pied, densité du matériau. L'imprimante l'exécute avec précision. Aucune interprétation par un tiers. Ce que vous prescrivez à l'écran est exactement ce que votre patient reçoit.
Dois-je affecter du personnel au fonctionnement de l'imprimante?
Non. Chargez le matériau, lancez l'impression et allez voir votre prochain patient: l'imprimante fonctionne de façon autonome. Aucune surveillance, aucune supervision technique, aucune embauche supplémentaire. Le flux complet, du numérisation au dispositif fini, s'insère dans votre horaire de patients sans le perturber.
Qui me soutient si je rencontre un problème?
Un podiatre en pratique répond à chaque demande de soutien: pas un centre d'appels, pas un robot. Vous joignez quelqu'un qui comprend votre contexte clinique et qui parle votre langue. La plupart des problèmes se règlent à distance en quelques heures. Si l'imprimante tombe en panne, notre service d'impartition prend le relais immédiatement, pour que vos patients n'attendent jamais.
Y a-t-il un contrat à long terme?
Non. Vous pouvez commencer avec le modèle d'impartition, sans aucun investissement initial: vous envoyez les numérisations et recevez les dispositifs finis en quelques jours. Vous passez à la production en clinique quand votre volume justifie l'imprimante. Aucun engagement à l'une ou l'autre des étapes.
Et si le système était trop complexe pour ma clinique?
C'est précisément cette inquiétude qui explique l'existence de Podform3D. Le système a été bâti par un clinicien exaspéré par des procédés de laboratoire trop complexes: la simplicité n'est pas une considération secondaire, c'est le point de départ. Si après l'intégration vous n'êtes pas à l'aise de produire des orthèses de façon autonome, nous restons avec vous jusqu'à ce que vous le soyez. Sans frais additionnels. Sans limite de temps.
Découvrir le reste du site
Contactez Dr Antonin Bérubé à antonin@podform3d.com.
Print custom orthotics right in your clinic.
From your patient's foot scan to finished orthotics in hours, with no manual work. Built by a podiatrist for foot care professionals worldwide.
Why Podform3D
- In-clinic manufacturing, full clinical control, margins kept in your practice.
- Orthotics ready in hours, not weeks. No lab callbacks, no follow-up appointments.
- Autonomous belt printer: 72+ hours unmanned operation, runs while you treat patients.
- Zero dedicated fabrication staff, zero dust, zero waste.
- Operational in 48 hours with full training and unlimited support.
The workflow
- Scan the foot with any 3D scanner, iPad, or foam impression box.
- Configure the prescription: arch height, multi-density zones, postings, corrections.
- Print on the autonomous belt printer while you see patients.
- Apply the top cover and deliver the same day.
Two paths
- Outsource via our certified lab network (zero capital investment, 7-day delivery).
- Produce in-clinic with the Podform3D belt printer (full control, lowest per-pair cost).
Questions clinicians ask before switching
How much does in-clinic 3D orthotic printing cost?
Podform3D offers a monthly SaaS subscription with transparent, predictable pricing. Most clinics see ROI within a few months. Use our savings calculator at podform3d.com/check-my-savings to see your personalized numbers.
Do I need 3D printing experience to use Podform3D?
No. Podform3D is designed for foot care professionals with zero 3D printing experience. The system includes a guided configurator, autonomous belt printer that runs unattended, and full training. Most clinics are operational within 48 hours.
How long does it take to produce a pair of custom orthotics?
From scan to finished orthotic, the process takes 2-4 hours. Scanning takes under 2 minutes, configuration takes about 5 minutes, and the printer runs autonomously. Your orthotics are ready the same day.
What materials are used in Podform3D orthotics?
Podform3D orthotics use clinical-grade thermoplastic with multi-density zones. The material allows variable stiffness across arch, heel, and forefoot regions. For outsourced options, SLS-grade Nylon 11, Nylon 12, and Polypropylene are available.
Can I use my own 3D scanner with Podform3D?
Yes. Podform3D works with any 3D foot scanner or iPad with LiDAR. You scan in under 2 minutes, import into the Podform3D configurator, and design the orthotic. No proprietary hardware lock-in.
What foot conditions can 3D-printed orthotics treat?
3D-printed orthotics from Podform3D treat plantar fasciitis, flat feet, heel pain, metatarsalgia, hallux valgus, Morton's neuroma, tendinitis, and other biomechanical conditions. Multi-density zones allow precise load redistribution tailored to each patient.
How do 3D-printed orthotics compare to traditional custom orthotics?
3D-printed orthotics offer higher dimensional accuracy, faster turnaround (ready in hours instead of weeks), significant production cost savings, and easy reprinting for adjustments. Clinical studies show comparable or superior biomechanical outcomes.
What is the ROI of in-clinic 3D orthotic printing?
Most clinics see ROI within a few months. Clinics producing in-clinic see significant savings versus external lab costs. Use our savings calculator at podform3d.com/check-my-savings for your specific numbers.
Can I outsource 3D-printed orthotics without buying a printer?
Yes. Podform3D offers an outsourcing path through our certified local partner network. You design in the configurator and receive SLS-grade Nylon 11, Nylon 12, or Polypropylene orthotics within 7 days. Zero capital investment required.
How many orthotics can the Podform3D printer produce per day?
The autonomous belt printer produces up to 5 pairs per day and runs unattended for 72+ hours continuously. Multiple printers can be run in parallel for higher volume clinics.
Is Podform3D available outside Canada?
Yes. Podform3D serves foot care professionals across North America. The free sample ships anywhere in North America, and the full system includes remote setup, training, and unlimited support.
What are multi-density zones in orthotics?
Multi-density zones allow different stiffness levels across the arch, heel, and forefoot of a single orthotic. This is achieved through variable infill patterns in 3D printing, delivering targeted support where each patient needs it without separate material layers.
Who founded Podform3D?
Podform3D was founded by Dr. Antonin Berube, a practicing podiatrist in Quebec, Canada. He built the system after years of frustration with external orthotic labs. Podform3D won Innovation of the Year from Quebec Science.
Explore the rest of the site
Contact Dr. Antonin Berube at antonin@podform3d.com.